Differences

This shows you the differences between two versions of the page.

--- nextpvr [2019/06/24 01:39] – [NextPVR Configuration – HDHomeRun PRIME] neds
+++ nextpvr [2019/12/09 02:01] (current) – neds
@@ Line 3: / Line 3: @@
 <lead>NextPVR is a third party DVR software program that can be used with HDHomeRun hardware. It is unrelated to the HDHomeRun DVR service.</lead>
-===== Setting up =====
+===== Setting up (NextPVR v4) =====
+<WRAP indent>
+<WRAP center info 80%>If you are using NextPVR v5 or later, the instructions for setting up an HDHomeRun will be different.</WRAP>
 ==== NextPVR Configuration – ATSC/QAM/DVB-T/DVB-C ====
+<WRAP indent>
   - Download and install the latest HDHomeRun software from **[[downloads]]**.
   - Open **HDHomeRun Setup**.
-  - On the **Location** tab, set the **Country** and **Zip/Postal Code**.
-  - On the **Applications** tab, set the **Main Application** to **Other:ATSC/QAM**.
   - On the **Tuners** tab, select the correct signal source for your tuners.
   - On the tab corresponding to your signal, click **Scan**.
@@ Line 35: / Line 38: @@
   - Click **OK**.
+</WRAP>
 ==== NextPVR Configuration – HDHomeRun PRIME ====
+<WRAP indent>
   - Download and install the latest HDHomeRun software from **[[downloads]]**.
   - Open **HDHomeRun Setup**.
-  - On the **Location** tab, set the **Country** and **Zip/Postal Code**.
-  - On the **Applications** tab, set the **Main Application** to **NextPVR**.
   - On the **Tuners** tab, set the **Signal Source** to **CableCARD** for each of your HDHomeRun PRIME tuners.
   - On the **Tuners** tab in **HDHomeRun Setup**, click on one of the Tuner IDs to access your HDHomeRun PRIME’s webpage. This can also be done by clicking the link on the Device tab in HDHomeRun Config GUI, or by directly navigating to the IP address of your HDHomeRun.
@@ Line 57: / Line 59: @@
   - Follow the instructions in the **Schedules Direct** section below to configure EPG data.
+</WRAP>
 ==== Schedules Direct configuration (North America only) ====
+<WRAP indent>
 Note: you must have a subscription to **[[http://www.schedulesdirect.org/|Schedules Direct]]** in order to use their EPG data. This is required for any EPG data for HDHomeRun PRIME, and recommended for ATSC/clear QAM.
-  - Click on Channels on the left side.
+  - Click on **Channels** on the left side.
-  - For those in North America using the Schedules Direct service for EPG, double click on one of your channels. Set the EPG Source to Schedules Direct, enter your Schedules Direct username and password, and click Download.
+  - For those in North America using the Schedules Direct service for EPG, **double click on one of your channels**. Set the EPG Source to **Schedules Direct**, enter your Schedules Direct username and password, and click **Download**.
-  - Select the correct lineup, then the mapping for that channel, and click OK.
+  - Select the correct lineup, then the mapping for that channel, and click **OK**.
-  - Click on Bulk Map.
+  - Click on **Bulk Map**.
-  - Select Schedules Direct as the EPG source for another channel, then select the mapping for it. You should get a prompt asking if you want it to attempt automatic mapping. Click Yes.
+  - Select **Schedules Direct** as the EPG source for another channel, then select the mapping for it. You should get a prompt asking if you want it to attempt automatic mapping. Click **Yes**.
-  - Correct any listings that were not set, then click OK.
+  - Correct any listings that were not set, then click **OK**.
-  - Click Update EPG.
+  - Click **Update EPG**.
-  - Click OK.
+  - Click **OK**.
+</WRAP>
+</WRAP>
 ===== FAQ =====
+<WRAP indent>
 <btn type="success" size="xs" icon="fa fa-chevron-right">[[:FAQ|See also: other FAQ listings]]</btn>
 ==== No Channels Found in Scan ====
+<WRAP indent>
 Check your firewall configuration and make sure that the NextPVR, NRecord, and NDigitalHost programs have full network access.
@@ Line 80: / Line 90: @@
 For HDHomeRun PRIME, make sure that you are running a firmware version of 20130328 or newer and that you have completed a channel scan in HDHomeRun Setup.
+</WRAP>
 ==== No video or audio ====
+<WRAP indent>
 Check your firewall configuration and make sure that the NextPVR, NRecord, and NDigitalHost programs have full network access.
 In the codec configuration area in NextPVR, make sure that you have selected decoders for MPEG2, H.264, and AC3.
+</WRAP>
+</WRAP>
 {{tag>third_party_app}}

third party app