Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
tech [2026/03/24 04:32] – nedstech [2026/04/11 01:39] (current) – neds
Line 1: Line 1:
 ====== SiliconDust TECH manual ====== ====== SiliconDust TECH manual ======
-<lead>These pages consolidates documentation relating to the commercial-grade TECH product line from SiliconDust.</lead>+<lead>Documentation relating to the commercial TECH product line from SiliconDust.</lead>
  
 ===== Hardware ===== ===== Hardware =====
 <WRAP indent> <WRAP indent>
  
 +==== Current models ====
 +<WRAP indent>
 +
 +^ Model numbers  ^ Tuners ^ Signal type ^ Size ^ 
 +^ TECH5-16US-4X4 | 16 (4 modules of 4 tuners) | ATSC 1.0, QAM64/256 | 1U 19" rack-mount | 
 +| | //Power supply information and other notes:// \\  |||
 +^ TECH5-16DT-4X4 | 16 (4 modules of 4 tuners) | DVB-T1, DVB-T2, DVB-C | 1U 19" rack-mount | 
 +| | //Power supply information and other notes:// \\  |||
 +^ TECH-4K | 4 (1 module of 4 tuners) | **Tuners 0+1:** ATSC 3.0, ATSC 1.0, QAM64/256 \\ **Tuners 2+3:** ATSC 1.0, QAM64/256 | 3.4"x3.4"x0.8" | 
 +| | //Power supply information and other notes:// \\ <wrap>5Volt 1.5Amp regulated power adapter (higher Amp rating ok) \\  1.7mm ID / 4.0mm OD plug, 9.5mm depth, center positive \\  Max 5.25V @ no-load \\  Min 4.75V @ 1.5A \\  Noise <= 150mVp-p </wrap> |||
 +^ TECH5-4K8-2X4 | 8 (4 modules of 2 tuners) | ATSC 3.0, ATSC 1.0, QAM64/256 | 1U 19" rack-mount | 
 +| | //Power supply information and other notes:// \\  |||
 +
 +</WRAP>
 +==== Past models (still supported) ====
 +<WRAP indent>
 +
 +<button collapse="past">Click to see table of past models</button>
 + 
 +<collapse id="past" collapsed="true">
 +
 +^ Model numbers  ^ Tuners ^ Signal type ^ Size ^ 
 +| TECH-US | 
 +| TECH3-US | 
 +| TECH3-8US-2X4 | 
 +| TECH4-2US | 
 +| TECH4-8US-2X4 | 
 +| TECH4-8IS-2X4 | 
 +| TECH3-EU | 
 +| TECH3-8EU-2X4 | 
 +| TECH4-2DT | 
 +| TECH4-8DT-2X4 | 
 +| TECH3-6CC-3X2 | 
 +| TECH3-3CC | 
 +| TECH3-8DC-4X2 | 
 +| TECH5-16DC-4X4 | 
 +</collapse>
 +
 +</WRAP>
 +==== LEDs and ports ====
 +<WRAP indent>
 +
 +
 +
 +</WRAP>
 ==== Power ==== ==== Power ====
 <WRAP indent> <WRAP indent>
-All devices should be used with the included power supply (dual-tuner models) or power cable (HDRack models).+ 
 +All devices should be used with the included power supply or power cable.
  
 </WRAP> </WRAP>
 ==== Ethernet ==== ==== Ethernet ====
 <WRAP indent> <WRAP indent>
 +
 Connect the Ethernet port(s) to a network switch. On models with multiple ports, all ports must be connected in order for all tuners to be accessible. A single port can be directly connected to the network interface on a PC to access that specific device. All ports are auto-crossover so a standard Ethernet cable can be used. Connect the Ethernet port(s) to a network switch. On models with multiple ports, all ports must be connected in order for all tuners to be accessible. A single port can be directly connected to the network interface on a PC to access that specific device. All ports are auto-crossover so a standard Ethernet cable can be used.
  
 </WRAP> </WRAP>
 +
 </WRAP> </WRAP>
-===== Downloads =====+===== Additional Tools and Software =====
 <WRAP indent> <WRAP indent>
  
Line 28: Line 76:
 <WRAP indent> <WRAP indent>
  
-Download and install the latest Windows release of the HDHomeRun software: https://download.silicondust.com/hdhomerun/hdhomerun_tech_windows.exe+Download and install the latest Windows release of TECH Setup utility: https://download.silicondust.com/hdhomerun/hdhomerun_tech_windows.exe
  
 The HDHomeRun Setup wizard is optional. The HDHomeRun Setup wizard is optional.
Line 38: Line 86:
 <WRAP indent> <WRAP indent>
  
-Download and extract the libhdhomerun archive.+Download and extract the libhdhomerun archive: https://download.silicondust.com/hdhomerun/libhdhomerun.tgz
  
 Run "make" to compile hdhomerun_config (systems that use a non-GNU make by default may need to install and use "gmake" instead). Run "make" to compile hdhomerun_config (systems that use a non-GNU make by default may need to install and use "gmake" instead).
Line 45: Line 93:
  
 </WRAP> </WRAP>
 +
 +</WRAP>
 +===== Command Line Utility (hdhomerun_config) =====
 +<WRAP indent>
 +
 +Open a command prompt or terminal window and change directory to the HDHomeRun installation directory: "C:\Program Files\Silicondust\HDHomeRun\"
 +
 +The list of supported commands can be obtained by running hdhomerun_config without any parameters:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config discover
 +hdhomerun_config <id> get help
 +hdhomerun_config <id> get <item>
 +hdhomerun_config <id> set <item> <value>
 +hdhomerun_config <id> scan <tuner> [<filename>]
 +hdhomerun_config <id> save <tuner> <filename>
 +hdhomerun_config <id> upgrade <filename>
 +</code>
 +</WRAP>
 +
 +==== Discover devices on the network ====
 +<WRAP indent>
 +
 +The discover command will find devices that are on the same subnet as the host:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config discover
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +==== Sending commands to a specific device ====
 +<WRAP indent>
 +
 +The “<id>” shown above represents a unique identifier for a device, this can be either Device ID, or IP address:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config <device id> get help
 +hdhomerun_config <ip address> get help
 +</code>
 +</WRAP>
 +
 +To address by Device ID the device must be on the same subnet as the host.
 +
 +A Device ID of FFFFFFFF can be used as a wild card for the first device found on the network. Do not use this syntax if there are multiple devices on the network, as the device used will be random based on discovery order, which may change between commands.
 +
 +</WRAP>
 +</WRAP>
 +
 +===== Supported Commands =====
 +<WRAP indent>
 +
 +The get/set options supported by a specific device can be queried using the get help command:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config <id> get help
 +</code>
 +</WRAP>
 +
 +Example output:
 +
 +<WRAP indent>
 +<code>
 +/card/status Get status of CableCARD (6CC only)
 +/oob/channel <modulation>:<freq> Get/set out of band channel (TECH3-CC only)
 +/oob/debug Get out of band channel debug info (TECH3-CC only)
 +/oob/status Get out of band channel status info (TECH3-CC only)
 +/sys/boot <config> Get/set boot configuration
 +/sys/copyright Get copyright information
 +/sys/debug Get/set system debug information
 +/sys/features Get system feature information
 +/sys/hwmodel Get system hardware model string
 +/sys/ipaddr dhcp|"<ip> <mask> <gw> <dns>" Get/set system IP address
 +/sys/model Get/set model string
 +/sys/restart <resource> Restart device/component, example "restart self" will reboot the unit
 +/sys/version Get firmware version
 +/tuner<n>/channel <modulation>:<freq|ch> Get/set channel
 +/tuner<n>/channelmap <channelmap> Get/set channelmap
 +/tuner<n>/debug Get tuner debug information
 +/tuner<n>/filter "0x<nnnn>-0x<nnnn> […]" Get/set tuner PID filter
 +/tuner<n>/lockkey Get/set tuner locking
 +/tuner<n>/plotsample Get raw plotsample data from tuner
 +/tuner<n>/program <program number> Get/set MPEG program
 +/tuner<n>/streaminfo Get list of programs on current channel
 +/tuner<n>/status Get tuner status
 +/tuner<n>/target <ip>:<port> Get/set stream target
 +/tuner<n>/target forward ATSC 3.0 only. Forwards all multicast IP packets to the LAN
 +/tuner<n>/vchannel <vchannel> Get/set virtual channel number (TECH3-CC, TECH4 and later)
 +/tuner<n>/vstatus Get/set subscription/protection status (TECH3-CC only)
 +/tuner<0|1>/plpinfo ATSC 3.0 only
 +/tuner<0|1>/l1detail ATSC 3.0 only
 +</code>
 +</WRAP>
 +
 +==== Channel scan ====
 +<WRAP indent>
 +To run a channel scan:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> scan /tuner<n> [log filename]
 +Example: hdhomerun_config FFFFFFFF scan /tuner0 scan0.log
 +</code>
 +</WRAP>
 +
 +This command will scan all channels on the selected channel map plus any additional channel maps associated with the selected channel map. All standard modulation types for the selected channel map are tested.
 +
 +When a digital channel is found it will identify the programs on the channel.
 +
 +The log filename is optional; if included it will log to the given filename.
 +
 +</WRAP>
 +==== Tuning a physical channel ====
 +<WRAP indent>
 +
 +To set a channel use the set channel command:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> set /tuner<n>/channel <modulation>:<frequency>
 +Format: hdhomerun_config <id> set /tuner<n>/channel <modulation>:<channel>
 +Example: hdhomerun_config FFFFFFFF set /tuner0/channel auto:651000000
 +Example: hdhomerun_config FFFFFFFF set /tuner0/channel auto:60
 +</code>
 +</WRAP>
 +
 +To auto-detect the modulation type use “auto” for the modulation.
 +
 +Supported modulation types can be queried with the get sys-features command:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config <id> get /sys/features
 +</code>
 +</WRAP>
 +
 +To stop the tuner set the channel to none:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> set /tuner<n>/channel none
 +Example: hdhomerun_config FFFFFFFF set /tuner0/channel none
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +==== Tuning a virtual channel ====
 +<WRAP indent>
 +TECH3-CC, TECH4, and later models support tuning by virtual channel number.
 +
 +To set a virtual channel use the set vchannel command:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> set /tuner<n>/vchannel <virtual channel>
 +Example: hdhomerun_config FFFFFFFF set /tuner0/vchannel 702
 +</code>
 +</WRAP>
 +
 +To stop the tuner set the vchannel to none:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> set /tuner<n>/vchannel none
 +Example: hdhomerun_config FFFFFFFF set /tuner0/vchannel none
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +==== Checking the signal strength ====
 +<WRAP indent>
 +
 +The basic signal information can be obtained by using the get status command:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> get /tuner<n>/status
 +Example: hdhomerun_config FFFFFFFF get /tuner0/status
 +</code>
 +</WRAP>
 +
 +Example output:
 +
 +<WRAP indent>
 +<code>
 +ch=qam:33 lock=qam256 ss=83(-10dBmV) snq=90(29dB) seq=100 bps=38807712 pps=0
 +</code>
 +</WRAP>
 +
 +  * ch = channel requested
 +  * lock = actual modulation detected
 +  * ss = signal strength.
 +  * snq = signal to noise quality (MER).
 +  * seq = symbol error quality (based on the number of uncorrectable digital errors detected).
 +  * bps = raw channel bits per second.
 +  * pps = packets per second sent through the network.
 +
 +More advanced information can be obtained by using the get debug command:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <device id> get /tuner<n>/debug
 +Example: hdhomerun_config FFFFFFFF get /tuner0/debug
 +</code>
 +</WRAP>
 +
 +Example output:
 +
 +<WRAP indent>
 +<code>
 +tun: ch=qam:33 lock=qam256 ss=84 snq=88 seq=100 dbg=22081-6930
 +dev: resync=0 overflow=0
 +ts: bps=38809216 ut=94 te=0 miss=0 crc=0
 +flt: bps=38809216
 +net: pps=0 err=0 stop=0
 +</code>
 +</WRAP>
 +
 +Each line contains a prefix to indicate the type of data, followed by the values.
 +
 +  * tun = tuner status
 +    * see above section
 +  * dev = device status
 +  * ts = transport stream
 +    * bps = bits per second
 +    * ut = utilization percentage (100% is filled to capacity)
 +    * te = transport error counter (uncorrectable reception error)
 +    * miss = missed packet counter (jump in sequence numbers)
 +    * crc = crc error counter
 +  * flt = results after pid filtering
 +    * bps = bits per second
 +  * net = network status
 +    * pps = packets per second
 +    * err = packets or TS frames dropped before transmission.
 +    * stop = reason for stopping the stream
 +
 +The counters are reset to zero upon a channel change, but may indicate a small number of errors caused before the tuner locks on the channel. As a result, diagnostics should be based on the change in values over time, and not the initial values.Detecting the programs on a physical channel:
 +
 +The device will detect the programs (sub-channels). Use the get streaminfo command to query the detected programs:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> get /tuner<n>/streaminfo
 +Example: hdhomerun_config FFFFFFFF get /tuner0/channel streaminfo
 +</code>
 +</WRAP>
 +
 +The output format is:
 +
 +<WRAP indent>
 +<code>
 +<program number>: <virtual major>.<virtual minor> [<name>] [(<flags>)]
 +</code>
 +</WRAP>
 +
 +Example output:
 +
 +<WRAP indent>
 +<code>
 +3: 20.1 KBWB-HD
 +4: 20.4 AZTECA
 +</code>
 +</WRAP>
 +
 +Digital cable does not always provide the channel name or virtual channel number:
 +
 +<WRAP indent>
 +<code>
 +1: 0.0
 +2: 0.0 (encrypted)
 +3: 0.0 (control)
 +</code>
 +</WRAP>
 +
 +It may take several seconds after setting the channel for the stream information to be fully populated (depending on how long the channel takes to lock and how often the stream information is sent by the broadcaster/cable provider).
 +
 +</WRAP>
 +==== Filtering by program (sub-channel) ====
 +<WRAP indent>
 +
 +Automatic PID filtering by program number or virtual channel number:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> set /tuner<n>/program <program number>
 + hdhomerun_config <id> set /tuner<n>/program <virtual channel number>
 +Example: hdhomerun_config FFFFFFFF set /tuner0/program 3
 + hdhomerun_config FFFFFFFF set /tuner0/program 11.2
 +</code>
 +</WRAP>
 +
 +When filtering by program the MPEG TS tables are generated by the device. The result is a valid single-program transport stream.
 +
 +The program filter is cleared when a set channel or a set filter command is received.
 +
 +**Advanced:** By default the PAT and PMT are generated. To also generate a ATSC-style TVCT use:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config <id> set /tuner<n>/program "<program number> tvct_from_pmt=<virtual major>.<virtual
 +minor>(<name>)"
 +</code>
 +<code>
 +Example: hdhomerun_config <id> set /tuner0/program "3 tvct_from_pmt=11.2(TEST)"
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +==== Filtering by PID ====
 +<WRAP indent>
 +
 +The TECH supports arbitrary hardware PID filtering:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> set /tuner<n>/filter <filter>
 +Example: hdhomerun_config FFFFFFFF set /tuner0/filter "0x0000-0x1FFF"
 + hdhomerun_config FFFFFFFF set /tuner0/filter "0x0000 0x0030-0x0033 0x1FFB"
 +</code>
 +</WRAP>
 +
 +When filtering by PID the stream is filtered but otherwise unmodified.
 +
 +The filter is cleared to pass-all (0x0000-0x1FFF) when a set channel command is received.
 +
 +</WRAP>
 +==== Saving a stream ====
 +<WRAP indent>
 +
 +The hdhomerun_config command can be used to automate the process of saving to the local filesystem:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> save /tuner<n> <filename>
 +Example: hdhomerun_config FFFFFFFF save /tuner0 capture.ts
 +</code>
 +</WRAP>
 +
 +While saving the stream, a single period “.” will be displayed every second. Errors will be indicated by
 +a letter.
 +
 +Example output:
 +<WRAP indent>
 +<code>
 +............n...............................n..........ts..........
 +-- Video statistics --
 +23323 packets recieved, 2 network errors, 1 transport errors, 1 sequence errors
 +</code>
 +</WRAP>
 +
 +**Advanced:** A filename of “null” indicates no file should be created, allowing the use of the save command as a diagnostic tool.
 +
 +**Advanced:** “-” may be used as a filename to indicate standard output, allowing the save command to be used as a pipe on supported platforms.
 +
 +<WRAP indent>
 +<code>
 +Example: hdhomerun_config FFFFFFFF save /tuner0 - | vlc -
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +==== Streaming to a target machine ====
 +<WRAP indent>
 +
 +Set the target IP address and port number using the set target command:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> set /tuner<n>/target udp://<ip>:<port>
 +Format: hdhomerun_config <id> set /tuner<n>/target rtp://<ip>:<port>
 +Example: hdhomerun_config FFFFFFFF set /tuner0/target udp://192.168.1.100:5000
 +Example: hdhomerun_config FFFFFFFF set /tuner0/target rtp://192.168.1.100:5000
 +</code>
 +</WRAP>
 +
 +The target machine must be listening on the given UDP port. The TECH will automatically clear the target if a ICMP port unreachable message is received when sending to a unicast address. To override this, add no_clear to the target.
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> set /tuner<n>/target "udp://<ip>:<port> no_clear"
 +Format: hdhomerun_config <id> set /tuner<n>/target "rtp://<ip>:<port> no_clear"
 +Example: hdhomerun_config FFFFFFFF set /tuner0/target "udp://192.168.1.100:5000 no_clear"
 +Example: hdhomerun_config FFFFFFFF set /tuner0/target "rtp://192.168.1.100:5000 no_clear"
 +</code>
 +</WRAP>
 +
 +A global broadcast (255.255.255.255), subnet broadcast, or multicast target can be specified however care must be taken to ensure that the traffic will not cause problems with other devices on the network.
 +
 +If the local network is bridged to a wireless network then the AP will typically transmit at a low broadcast speed saturating the wireless network.
 +
 +The time-to-live (TTL) defaults to 64. To configure a lower TTL use the following format (quotes required):
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> set /tuner<n>/target "udp://<ip>:<port> ttl=<n>"
 +Format: hdhomerun_config <id> set /tuner<n>/target "rtp://<ip>:<port> ttl=<n>"
 +Example: hdhomerun_config FFFFFFFF set /tuner0/target "udp://192.168.1.100:5000 ttl=8"
 +Example: hdhomerun_config FFFFFFFF set /tuner0/target "rtp://192.168.1.100:5000 ttl=8"
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +==== Example: Streaming to VLC ====
 +<WRAP indent>
 +
 +Run VLC: Media, Open Network Stream. Select UDP/RTP. Specify port 5000.
 +
 +Discover the device:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config discover
 +</code>
 +</WRAP>
 +
 +Run a channel scan:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config FFFFFFFF scan /tuner0 scan0.log
 +</code>
 +</WRAP>
 +
 +Set the physical channel:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config FFFFFFFF set /tuner0/channel auto:651000000
 +</code>
 +</WRAP>
 +
 +Check sub-programs:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config FFFFFFFF get /tuner0/streaminfo
 +</code>
 +</WRAP>
 +
 +Select a sub-program:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config FFFFFFFF set /tuner0/program 3
 +</code>
 +</WRAP>
 +
 +Set the target:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config FFFFFFFF set /tuner0/target udp://<ip address of pc>:5000
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +</WRAP>
 +
 +===== HTTP Streaming =====
 +<WRAP indent>
 +<btn type="success" size="xs" icon="fa fa-chevron-right">[[:http_api|See also: HTTP API documentation]]</btn>
 +
 +TECH3-CC, TECH4, and later models can be used to stream via HTTP (unicast only) to VLC or other clients.
 +
 +<WRAP indent>
 +<code>
 +Format: http://<ip address of device>:5004/auto/v<vchannel number>
 +Example: http://10.10.10.2:5004/auto/v721
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +
 +===== Lineup file =====
 +<WRAP indent>
 +TECH3-CC, TECH4, and later models support virtual channel lineup information. This is available in XML and JSON format.
 +
 +<WRAP indent>
 +<code>
 +http://<ip address of device>/lineup.xml
 +http://<ip address of device>/lineup.json
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +
 +===== Datacast operation =====
 +<WRAP indent>
 +
 +TECH units support Datacast TCP/IP over OTA broadcast. Datacasting often provides news, weather, traffic, stock market, and other information which may or may not relate to the program[s] it is carried with. An electronic program guide is usually included. Datacast TCP-IP packets are reassembled and then routed to the LAN port.
 +
 +Example:
 +
 +Discover the device:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config discover
 +</code>
 +</WRAP>
 +
 +Set the physical channel:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config FFFFFFFF set /tuner0/channel auto:651000000
 +</code>
 +</WRAP>
 +
 +Set the datacast PID:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config FFFFFFFF set /tuner0/filter 0x0A00
 +</code>
 +</WRAP>
 +
 +Set the target:
 +
 +<WRAP indent>
 +<code>
 +hdhomerun_config FFFFFFFF set /tuner0/target datacast
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +
 +===== Boot scripts =====
 +<WRAP indent>
 +
 +The /sys/boot variable allows the TECH unit to automatically set variables at startup, allowing you to preserve settings across power outages or simply set the power on defaults.
 +
 +The syntax for the /sys/boot consists of multiple lines of text; a variable name followed by a single space and then the value: (there should not be any space before the variable name)
 +
 +<WRAP indent>
 +<code>
 +<variable1> <value of variable1>
 +<variable2> <value of variable2>
 +...
 +<variableN> <value of variableN>
 +</code>
 +</WRAP>
 +
 +Example (save as boot.txt):
 +
 +<WRAP indent>
 +<code>
 +/tuner0/channelmap us-cable
 +/tuner0/channel 103
 +/tuner0/program 4
 +</code>
 +</WRAP>
 +
 +To place a wait period between commands you can use the "sleep" command followed by the number of seconds:
 +
 +<WRAP indent>
 +<code>
 +<first command>
 +
 +sleep 60
 +
 +<next command>
 +</code>
 +</WRAP>
 +
 +
 +To store the configuration to the device:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> set /sys/boot - < filename
 +Example: hdhomerun_config FFFFFFFF set /sys/boot - < boot.txt
 +</code>
 +</WRAP>
 +
 +Changes will be applied the next boot; to execute the new /sys/boot immediately:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <id> execute
 +Example: hdhomerun_config FFFFFFFF execute
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +===== Static IP assignment =====
 +<WRAP indent>
 +
 +A static IP address can be configured using the following command (the quotes are required as shown):
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <old ip> set /sys/ipaddr "<new ip> <subnet> <gateway>"
 +Example: hdhomerun_config 169.254.34.98 set /sys/ipaddr "10.10.20.43 255.255.255.0 10.10.20.1"
 +</code>
 +</WRAP>
 +
 +Note: The TECH requires a gateway when used to stream multicast, even if on the same subnet.
 +
 +==== Reverting to DHCP ====
 +<WRAP indent>
 +
 +The TECH can be configured for DHCP operation (default) using the following command:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <old ip> set /sys/ipaddr dhcp
 +Example: hdhomerun_config 169.254.34.98 set /sys/ipaddr dhcp
 +</code>
 +</WRAP>
 +
 +<WRAP info>
 +If you cannot access the TECH due to the IP address change, do the following to reset:
 +
 +Set a static IP on the computer in the 169.254.x.y range (e.g. 169.254.1.9) with a 255.255.0.0 subnet mask. The auto IP address for the TECH device will be randomly chosen within the 169.254.x.y range. Use the [[https://download.silicondust.com/hdhomerun/hdhomerun_tech_windows.exe|TECH Config GUI]] to locate it and reset the IP.
 +</WRAP>
 +
 +</WRAP>
 +
 +</WRAP>
 +
 +===== Setting the channel map =====
 +<WRAP indent>
 +
 +The channel map is a non-volatile configuration option that is used to set the channel to frequency table, to configure the channel scan table, and to optimize the auto-modulation detection.
 +
 +GUI: The channel map can be set for each tuner by running HDHomeRun Config (GUI).
 +
 +Command line: The channel map can be set for each tuner using the following command:
 +
 +<WRAP indent>
 +<code>
 +Format: hdhomerun_config <ip|id> set /tuner<n>/channelmap <channelmap>
 +Example: hdhomerun_config 10001000 set /tuner0/channelmap us-cable
 +Example: hdhomerun_config 10001000 set /tuner1/channelmap us-cable
 +</code>
 +</WRAP>
 +
 +Channel maps supported by US hardware:
 +
 +<WRAP indent>
 +^ Name ^ Description ^ Location ^
 +| us-bcast | Digital Antenna (ATSC). | US, Canada |
 +| us-cable | Digital Cable - Normal frequency layout. | US, Canada |
 +| us-hrc | Digital Cable - HRC frequency layout. | US, Canada |
 +| us-irc | Digital Cable - IRC frequency layout. | US, Canada |
 +</WRAP>
 +
 +Channel maps supported by DVB hardware:
 +
 +<WRAP indent>
 +^ Name ^ Description ^ Location ^
 +| au-bcast | Digital Antenna (Australia). | Australia |
 +| au-cable | Digital Cable (Australia). | Australia |
 +| eu-bcast | Digital Antenna (Europe). | Europe, New Zealand |
 +| eu-cable | Digital Cable (Europe). | Europe, New Zealand |
 +| tw-bcast | Digital Antenna (Taiwan). | Taiwan |
 +| tw-cable | Digital Cable (Taiwan). | Taiwan |
 +</WRAP>
 +
 +</WRAP>
 +===== Multicast =====
 +<WRAP indent>
 +
 +TECH supports multicast streaming within a network.
 +
 +  - Using HDHomeRun Config GUI or hdhomerun_config choose a desired channel and program number for each tuner. In this example we will use channel 19 program 3 on tuner 0 and channel 30 program 1 on tuner 1.
 +  - Choose a multicast IP address for each stream. As a general rule the multicast address should be in the range of 239.255.0.0 to 239.255.255.255. In this example we will use 239.255.1.1 and 239.255.1.2
 +  - Choose a destination (client) port number. The port should be outside the the well-known ports range (we recommend 50000+) and should be unique for each stream. In this example we will use 59001 and 59002.
 +  - Write the boot script (text file):<WRAP><code>
 +/tuner0/channelmap us-bcast
 +/tuner0/channel 19
 +/tuner0/program 3
 +/tuner0/target rtp://239.255.1.1:59001 ttl=64
 +
 +/tuner1/channelmap us-bcast
 +/tuner1/channel 30
 +/tuner1/program 1
 +/tuner1/target rtp://239.255.1.2:59002 ttl=64</code></WRAP>
 +  - Write the boot script to the device: <WRAP><code>hdhomerun_config 10010003 set /sys/boot - < boot.txt</code></WRAP>
 +  - Execute the boot script: <WRAP><code>hdhomerun_config 10010003 execute</code></WRAP>
 +  - Check the tuner status and target for each tuner. The packets-per-second “pps” number should be non-zero indicating that the device is sending the stream. <WRAP><code>hdhomerun_config 10010003 get /tuner0/debug
 +hdhomerun_config 10010003 get /tuner0/target
 +hdhomerun_config 10010003 get /tuner1/debug
 +hdhomerun_config 10010003 get /tuner1/target</code></WRAP>
 +
 +</WRAP>
 +===== Example Boot Script Configurations =====
 +<WRAP indent>
 +
 +Tuning 2 ATSC channels and streaming to multicast addresses using RTP:
 +
 +<WRAP indent>
 +<code>
 +/tuner0/channelmap us-bcast
 +/tuner0/channel 31
 +/tuner0/program 3
 +/tuner0/target rtp://239.255.1.1:59001
 +/tuner1/channelmap us-bcast
 +/tuner1/channel 8
 +/tuner1/program 1
 +/tuner1/target rtp://239.255.1.2:59002
 +</code>
 +</WRAP>
 +
 +Tuning 3 digital cable channels using a CableCARD and streaming to multicast addresses using RTP:
 +
 +<WRAP indent>
 +<code>
 +/tuner0/vchannel 702
 +/tuner0/target rtp://239.255.1.1:59001
 +/tuner1/vchannel 740
 +/tuner1/target rtp://239.255.1.2:59002
 +/tuner2/vchannel 771
 +/tuner1/target rtp://239.255.1.3:59003
 +</code>
 +</WRAP>
 +
 +Tuning 2 DVB-T channels in Australia and streaming to multicast addresses using UDP:
 +
 +<WRAP indent>
 +<code>
 +/tuner0/channelmap au-bcast
 +/tuner0/channel 5
 +/tuner0/program 20121
 +/tuner0/target udp://239.255.1.1:59001
 +/tuner1/channelmap au-bcast
 +/tuner1/channel 44
 +/tuner1/program 28753
 +/tuner1/target udp://239.255.1.2:59002
 +</code>
 +</WRAP>
 +
 +Tuning 2 DVB-C channels in Europe and streaming to a single PC, ignoring rejection messages from the PC due to a closed port:
 +
 +<WRAP indent>
 +<code>
 +/tuner0/channelmap eu-cable
 +/tuner0/channel 646
 +/tuner0/program 231
 +/tuner0/target udp://192.168.0.22:59001 no_clear
 +/tuner1/channelmap eu-cable
 +/tuner1/channel 770
 +/tuner1/program 24112
 +/tuner1/target udp://192.168.0.22:59002 no_clear
 +</code>
 +</WRAP>
 +
 +</WRAP>
 +===== HDHomeRun app =====
 +<WRAP indent>
 +
 +{{ :tech_guide.png?direct&400|}}
 +When using the TECH3-CC or TECH4 and later, the consumer [[:app|HDHomeRun app]] can be used, allowing the TECH to behave as a consumer HDHomeRun unit. To enable this the TECH will need to sync with the HDHomeRun guide server on the internet:
 +
 +  - Access the web interface of the TECH unit //(for example, <nowiki>http://192.168.0.49</nowiki> )//
 +  - Check the option **"Sync with guide server"**
 +  - All other features of the TECH can still be used in this mode.
 +
 +<WRAP clear/>
 +
 </WRAP> </WRAP>
  • Last modified: 2026/03/24 04:32